Study on Controlled Low Strength Materials using GGBS with Dredged Soil and M-Sand

Study on Controlled Low Strength Materials using GGBS with Dredged Soil and M-Sand

S. Loganayagan, S. Ramakrishnan, V. Jeevanantham, M. Gowtham

download PDF

Abstract. In general, CLSM mixtures contain common ingredients such as Portland cement, fly ash, good mixing and water. CLSM is forced to fill in the back material and not low-strength concrete, rather it can best be described as property which is designed as concrete and strength flow and strength as per requirement and used as a backfill to avoid soil issues. CLSM can be built with a variety of strengths and sizes, taking into account costs future requirements, low power CLSM will be required to allow future excavation, and if there is no space for future digging the energy can be high on the other hand, furthering the size of CLSM can be adjusted according to the cost and material requirements. However, some industrial products and recycled products are also accepted and promoted as long as they are available, costing a particular use and the necessary characteristics of a combination such as flow, power, extraction, and quantity are acceptable. The aim of this study was to test whether it was possible to apply red mud such as placing a portion of Portland cement in a low-power controlled (CLSM) component made of industrial-grade products. The control mixture was initially made from the Portland cement, fly ash, and water. Bleeding, flow, the initial time for the setting of new CLSM compounds is measured and subsequent complications include compression. Results-They performed well and complied with CLSM requirements at ACI 229 levels in terms of flow, bleeding rate, initial set-up time, uncompressed compression strength. Low power control devices (CLSM) remove the problems of ground receding to provide the strength of the supporting structure.

Low Strength Material, Dredged Soil, GGBS, M-Sand

Published online , 8 pages
Copyright © 2022 by the author(s)
Published under license by Materials Research Forum LLC., Millersville PA, USA

Citation: S. Loganayagan, S. Ramakrishnan, V. Jeevanantham, M. Gowtham, Study on Controlled Low Strength Materials using GGBS with Dredged Soil and M-Sand, Materials Research Proceedings, Vol. 23, pp 340-347, 2022


The article was published as article 39 of the book Sustainable Materials and Smart Practices

Content from this work may be used under the terms of the Creative Commons Attribution 3.0 licence. Any further distribution of this work must maintain attribution to the author(s) and the title of the work, journal citation and DOI.

[1] M. A. Fauzi, M. F. Arshad, and N. Md Nor, “Statistical models to develop optimised controlled low-strength materials with wastepaper sludge ash,” Constr. Build. Mater., vol. 286, p. 122816,2021.
[2] A. BarghiKhezerloo, S. M. Dehghan, and M. Sepasdar, “Using Dune Sand in Controlled Low-Strength Material for Backfilling: Field Installation and Numerical Simulation,” J. Pipeline Syst. Eng. Pract., vol. 12, no. 1, p. 04020055,2021.
[3] D. AhadzadehGhanad, A. Soliman, S. Godbout, and J. Palacios, “Properties of bio- based controlled low strength materials,” Constr. Build. Mater., vol. 262, p. 120742, 2020.
[4] S. P. Singh, K. Bhagya, and M. Mishra, Properties of Fly Ash-Based Controlled Low Strength Material, vol. 85.2020.
[5] C. P. Ramesh, H. P. Vageesh, T. Raghavendra, B. C. Udayashankar, and A. Shashishankar, Proportioning of CLSM Containing Class C Fly Ash, GGBS, Quarry Dust and Processed Slag Sand.2019.
[6] J. Zhang, J. Wang, X. Li, T. Zhou, and Y. Guo, “Rapid-hardening controlled low strength materials made of recycled fine aggregate from construction and demolition waste,” Constr. Build. Mater., vol. 173, pp. 81-89,2018.
[7] T. Manh Do, G. O. Kang, and Y. sang Kim, “Development of a new cementless binder for controlled low strength material (CLSM) using entirely by-products,” Constr. Build. Mater., vol. 206, pp. 576-589,2019.
[8] Chandra S., (2005), “Implications of using recycled construction and demolition waste as aggregate in concrete”, Session lead paper, International Conference on Sustainable Waste Management and Recycling, Cement Concrete Composite, 27(6), 738-741.
[9] Ishimoto H., Origuchi T., Yasuda M., (2000), “Use of papermaking sludge as new material”, Journal Material Civil Engineering 12(1), pp.310-313.
[10] Dhir RK, Leelawat T, Limbachiya MC., (2000), “Use of recycled concrete aggregate in high-strength concrete”, Materials Structure, vol. 33, 574-580.
[11] JianzhuangXiaoa, YuedongSuna, H. Falknerb, (2005), “Seismic performance of frame structures with recycled aggregate concrete”,Department of Building Engineering, Institute of Building Materials.
[12] Khaldoun Rahal, Ã, (2007), “Mechanical properties of concrete with recycled coarse aggregate Building and Environment”, Department of Civil Engineering, Kuwait University, 42, 407-415.
[13] Khalaf FM, DeVenny AlanS, (2004), “Recycling of demolished masonry rubble as coarse aggregate in Concrete”, ASCE J Mater Civil Eng, 331-340.
[14] Mozaffari E., O’Farrell M., Kinuthia J.M., Wild S., (2006), “Improving strength development of waste paper sludge ash by wet-milling”, Cement and Concrete Composites, 28, 144-152.
[15] Ramachandran VS., (1981), “Waste and by-products as concrete aggregates”, Canadian Building Digest Report, CBD-215, NRC,