Checkpoint Efficiency Analysis Method

Checkpoint Efficiency Analysis Method

CZERWIŃSKA Karolina, DWORNICKA Renata, PACANA Andrzej

Abstract. The use of multifaceted quality analyses contributes to increasing the efficiency of production processes and quality control as part of maintaining competitiveness. The aim of the study was to identify an integrally configured method for analysing the effectiveness of control points in the context of their ranking in terms of given variables. Verification of the model was carried out against the production process of an aluminium casting. The obtained ranking of the detection methods indicated the MT method as the most effective, which was influenced by the significant detection of critical non-conformities. The study observed little difference between the performance parameters of visual inspection and endoscopic testing, which is largely due to the detection of non-conformities of lower significance and the relatively low cost of testing. Further work will relate to the implementation of the model against other processes carried out in the company.

Keywords
Quality Management, Mechanical Engineering, Control Point, Efficiency, NDT Tests

Published online 9/1/2023, 13 pages
Copyright © 2023 by the author(s)
Published under license by Materials Research Forum LLC., Millersville PA, USA

Citation: CZERWIŃSKA Karolina, DWORNICKA Renata, PACANA Andrzej, Checkpoint Efficiency Analysis Method, Materials Research Proceedings, Vol. 34, pp 186-198, 2023

DOI: https://doi.org/10.21741/9781644902691-23

The article was published as article 23 of the book Quality Production Improvement and System Safety

Content from this work may be used under the terms of the Creative Commons Attribution 3.0 license. Any further distribution of this work must maintain attribution to the author(s) and the title of the work, journal citation and DOI.

References
[1] M. Plewa. M. Assessment of influence of products’ reliability on remanufacturing processes. Int. J. Perform. Eng 5 (2009) 463-470.
[2] A. Tubis. The Potentials in the Integration of Planning Enterprise Activity, Logistics and Transport 2010/1 (2010) 105-113.
[3] R. Ulewicz. Quality control system in production of the castings from spheroid cast iron, Metalurgija 42 (2003) 61-63.
[4] A. Pacana, K. Czerwińska. Analysis of the causes of control panel inconsistencies in the gravitational casting process by means of quality management instruments, Prod. Eng. Arch. 25 (2019) 12-16. https://doi.org/10.30657/pea.2019.25.03
[5] R. Wolniak. Operation manager and its role in the enterprise, Prod. Eng. Arch. 24 (2019) 1-4. https://doi.org/10.30657/pea.2019.24.01
[6] W. Dai, P.G. Maropoulos, Y. Zhao. Reliability modelling and verification of manufacturing processes based on process knowledge management. Int. J. Comput. Integr. Manuf. 28 (2015) 98 111. https://doi.org/10.1080/0951192X.2013.834462
[7] D. Klimecka-Tatar, M. Ingaldi. Assessment of the technological position of a selected enterprise in the metallurgical industry, Mater. Res. Proc. 17 (2020) 72 78. https://doi.org/10.21741/9781644901038-11
[8] M. Fertsch, K. Grzybowska, A. Stachowiak. Models of manufacturing systems – classification framework. Research in Logistics and Production 1 (2011) 45-51.
[9] M. Chlebus, S. Werbińska-Wojciechowska. Issues on Production Process Reliability Assessment – Review, Research in Logistics and Production 6 (2016) 481-497.
[10] A. Gazda et al. Study on improving the quality of stretch film by Taguchi method, Przemysl Chemiczny, 92 6(2013) 980-982.
[11] M.M. Helms. Encyclopedia of Management 5th Edition, Thompson Gale, Detroit, 2006, 211 211. ISBN 978-0787665562
[12] B. Clark. Managerial perceptions of marketing performance: efficiency, adaptability, effectiveness and satisfaction, J. Strategic Mark. 8 (2000) 3-25. https://doi.org/10.1080/096525400346286
[13] A. Pacana et al. Effect of selected factors of the production process of stretch film for its resistance to puncture, Przemysl Chemiczny 93 (2014), 2263-2264. https://doi.org/10.12916/przemchem.2014.2263
[14] W. Zong, X.H. Shen, L.C. Wang. Discussion on Enhancing Engineering Quality Supervision and Management by Information Technology, EBM 2011 Int. Conf. on Engineering and Business Management, 22-24 March 2011, Wuhan, China, 1440-1443. ISBN 978-1629932620
[15] E.A. Elsayed. Perspectives and challenges for research in quality and reliability engineering, Int. J. Prod. Res. 38 (2000) 1953-1976. https://doi.org/10.1080/002075400188438
[16] T. Hosokawa, Z. Miyagi. Quality engineering-based management: a proposal for achieving total optimisation of large systems, TQM Bus. Excel. 30 (2019) 182-194. https://doi.org/10.1080/14783363.2019.1665843
[17] G.J. Savage, S.M. Carr. Interrelating Quality and Reliability in Engineering Systems. Qual. Eng. 14 (2001) 137-152. https://doi.org/10.1081/QEN-100106893
[18] D. Malindžák, A. Pacana, H. Pačaiova. An effective model for the quality of logistics and improvement of environmental protection in a cement plant, Przemysl Chemiczny 96 (2017) 1958 1962.
[19] A. Jodejko-Pietruczuk, M. Plewa. Components’ rejuvenation in production with reused elements, Int. J. Perform. Eng. 10 (2014) 567-575.
[20] S. Borkowski, R. Ulewicz, J. Selejdak, M. Konstanciak, D. Klimecka-Tatar. The use of 3×3 matrix to evaluation of ribbed wire manufacturing technology, METAL 2012 – 21st Int. Conf. Metallurgy and Materials (2012), Ostrava, Tanger 1722-1728.
[21] R. Ulewicz. Outsorcing quality control in the automotive industry, MATEC Web of Conf. 183 (2018) art.03001. https://doi.org/10.1051/matecconf/201818303001
[22] R. Ulewicz, F. Nový. Quality management systems in special processes, Transp. Res. Procedia 40 (2019) 113-118. https://doi.org/10.1016/j.trpro.2019.07.019
[23] Ł.J. Orman Ł.J., N. Radek, J. Pietraszek, M. Szczepaniak. Analysis of enhanced pool boiling heat transfer on laser-textured surfaces. Energies 13 (2020) art. 2700. https://doi.org/10.3390/en13112700
[24] M. Szczepaniak et al. T. Use of the maximum power point tracking method in a portable lithium-ion solar battery charger, Energies 15 (2022) art.26. https://doi.org/10.3390/en15010026
[25] S. Maleczek et al. Tests of Acid Batteries for Hybrid Energy Storage and Buffering System—A Technical Approach, Energies 15 (2022) art.3514. https://doi.org/10.3390/en15103514
[26] A. Goroshko et al. Construction and practical application of hybrid statistically-determined models of multistage mechanical systems, Mechanika 20 (2014) 489-493. https://doi.org/10.5755/j01.mech.20.5.8221
[27] R. Ulewicz, M. Mazur. Economic aspects of robotization of production processes by example of a car semi-trailers manufacturer, Manuf. Technol. 19 (2019) 1054-1059. https://doi.org/10.21062/ujep/408.2019/a/1213-2489/MT/19/6/1054
[28] G. Filo, E. Lisowski, M. Domagała, J. Fabiś-Domagała, H. Momeni. Modelling of pressure pulse generator with the use of a flow control valve and a fuzzy logic controller, AIP Conf. Proc. 2029 (2018) art.20015. https://doi.org/10.1063/1.5066477
[29] M. Domagala et al. CFD Estimation of a Resistance Coefficient for an Egg-Shaped Geometric Dome, Appl. Sci. 12 (2022) art.10780. https://doi.org/10.3390/app122110780
[30] M. Domagala et al. The Influence of Oil Contamination on Flow Control Valve Operation, Mater. Res. Proc. 24 (2022) 1-8. https://doi.org/10.21741/9781644902059-1
[31] W. Przybył et al. Virtual Methods of Testing Automatically Generated Camouflage Patterns Created Using Cellular Automata, Mater. Res. Proc. 24 (2022) 66-74. https://doi.org/10.21741/9781644902059-11
[32] N. Radek et al. Operational tests of coating systems in military technology applications, Eksploat. i Niezawodn. 25 (2023) art.12. https://doi.org/10.17531/ein.2023.1.12
[33] W. Przybył et al. Microwave absorption properties of carbonyl iron-based paint coatings for military applications, Def. Technol. 22 (2023) 1-9. https://doi.org/10.1016/j.dt.2022.06.013
[34] N. Radek et al. Technology and application of anti-graffiti coating systems for rolling stock, METAL 2019 28th Int. Conf. Metall. Mater. (2019) 1127-1132. ISBN 978-8087294925
[35] N. Radek et al. Influence of laser texturing on tribological properties of DLC coatings, Prod. Eng. Arch. 27 (2021) 119-123. https://doi.org/10.30657/pea.2021.27.15
[36] N. Radek et al. Formation of coatings with technologies using concentrated energy stream, Prod. Eng. Arch. 28 (2022) 117-122. https://doi.org/10.30657/pea.2022.28.13
[37] N. Radek et al. The influence of plasma cutting parameters on the geometric structure of cut surfaces, Mater. Res. Proc. 17 (2020) 132-137. https://doi.org/10.21741/9781644901038-20
[38] N. Radek et al. The effect of laser treatment on operational properties of ESD coatings, METAL 2021 30th Ann. Int. Conf. Metall. Mater. (2021) 876-882. https://doi.org/10.37904/metal.2021.4212
[39] N. Radek et al. The WC-Co electrospark alloying coatings modified by laser treatment, Powder Metall. Met. Ceram. 47 (2008) 197-201. https://doi.org/10.1007/s11106-008-9005-7
[40] P. Kurp, H. Danielewski Metal expansion joints manufacturing by a mechanically assisted laser forming hybrid method – concept, Technical Transactions 119 (2022) art. e2022008. https://doi.org/10.37705/TechTrans/e2022008
[41] R. Ulewicz et al. Structure and mechanical properties of fine-grained steels, Period. Polytech. Transp. Eng. 41 (2013) 111-115. https://doi.org/10.3311/PPtr.7110
[42] D. Klimecka-Tatar, M. Ingaldi. Assessment of the technological position of a selected enterprise in the metallurgical industry, Mater. Res. Proc. 17 (2020) 72-78. https://doi.org/10.21741/9781644901038-11
[43] P. Jonšta et al. The effect of rare earth metals alloying on the internal quality of industrially produced heavy steel forgings, Materials 14 (2021) art.5160. https://doi.org/10.3390/ma14185160
[44] J. Pietraszek, N. Radek, A.V. Goroshko. Challenges for the DOE methodology related to the introduction of Industry 4.0. Production Engineering Archives 26 (2020) 190-194. https://doi.org/10.30657/pea.2020.26.33
[45] B. Jasiewicz et al. Inter-observer and intra-observer reliability in the radiographic measurements of paediatric forefoot alignment, Foot Ankle Surg. 27 (2021) 371-376. https://doi.org/10.1016/j.fas.2020.04.015
[46] J. Pietraszek. The modified sequential-binary approach for fuzzy operations on correlated assessments, LNAI 7894 (2013) 353-364. https://doi.org/10.1007/978-3-642-38658-9_32
[47] J. Pietraszek et al. Non-parametric assessment of the uncertainty in the analysis of the airfoil blade traces, METAL 2017 26th Int. Conf. Metall. Mater. (2017) 1412-1418. ISBN 978-8087294796
[48] J. Korzekwa et al. The influence of sample preparation on SEM measurements of anodic oxide layers, Pract. Metallogr. 53 (2016) 36-49. https://doi.org/10.3139/147.110367
[49] A. Gadek-Moszczak, P. Matusiewicz. Polish stereology – A historical review, Image Analysis and Stereology 36 (2017) 207-221. https://doi.org/10.5566/ias.1808
[50] M. Krynke et al. Maintenance management of large-size rolling bearings in heavy-duty machinery, Acta Montan. Slovaca 27 (2022) 327-341. https://doi.org/10.46544/AMS.v27i2.04
[51] P. Regulski, K.F. Abramek The application of neural networks for the life-cycle analysis of road and rail rolling stock during the operational phase, Technical Transactions 119 (2022) art. e2022002. https://doi.org/10.37705/TechTrans/e2022002
[52] M. Patek et al. Non-destructive testing of split sleeve welds by the ultrasonic TOFD method, Manuf. Technol. 14 (2014) 403-407. https://doi.org/10.21062/ujep/x.2014/a/1213-2489/MT/14/3/403
[53] I. Miletić, A. Ilić, R.R. Nikolić, R. Ulewicz, L. Ivanović, N. Sczygiol. Analysis of selected properties of welded joints of the HSLA Steels, Materials 13 (2020) art.1301. https://doi.org/10.3390/ma13061301
[54] N. Radek et al. Properties of Steel Welded with CO2 Laser, Lecture Notes in Mechanical Engineering (2020) 571-580. https://doi.org/10.1007/978-3-030-33146-7_65
[55] M. Ulewicz et al. Transport of lead across polymer inclusion membrane with p-tert -butylcalix[4]arene derivative , Physicochem. Probl. Miner. Process. 44 (2010) 245-256.
[56] M. Zenkiewicz et al. Modeling electrostatic separation of mixtures of poly(ϵ-caprolactone) with polyfvinyl chloride) or polyfethylene terephthalate), Przemysl Chemiczny 95 (2016) 1687 1692. https://doi.org/10.15199/62.2016.9.6
[57] M. Zenkiewicz, T. Zuk, J. Pietraszek, P. Rytlewski, K. Moraczewski, M. Stepczyńska. Electrostatic separation of binary mixtures of some biodegradable polymers and poly(vinyl chloride) or poly(ethylene terephthalate), Polimery/Polymers 61 (2016) 835-843. https://doi.org/10.14314/polimery.2016.835
[58] J. Fabiś-Domagała, G. Filo, H. Momeni, M. Domagała. Instruments of identification of hydraulic components potential failures, MATEC Web of Conf. 183 (2018) art.03008. https://doi.org/10.1051/matecconf/201818303008
[59] K. Knop et al. Evaluating and Improving the Effectiveness of Visual Inspection of Products from the Automotive Industry, Lecture Notes in Mechanical Engineering (2019) 231-243. https://doi.org/10.1007/978-3-030-17269-5_17
[60] P. Lempa, G. Filo. Analysis of Neural Network Training Algorithms for Implementation of the Prescriptive Maintenance Strategy, Mater. Res. Proc. 24 (2022) 281-287. https://doi.org/10.21741/9781644902059-41
[61] M. Gupta et al. Advances in applications of Non-Destructive Testing (NDT): A review, Adv. Mater. Process. Technol. 8 (2022) 2286-2307. https://doi.org/10.1080/2374068X.2021.1909332
[62] A. Sophian, G.Y. Tian, D. Taylor, J. Rudlin. Electromagnetic and eddy current NDT: a review, Insight: Non-Destr. Test. Condit. Monit. 43 (2001) 302-306.
[63] G. Davis et al. Laser ultrasonic inspection of additive manufactured components, Int. J. Adv. Manuf. Technol 102 (2019) 2571-2579. https://doi.org/10.1007/s00170-018-3046-y
[64] L.K. Shark, B.J. Matuszewski, J.P. Smith, M.R. Varley. Automatic feature-based fusion of ultrasonic, radiographic and shearographic images for aerospace NDT, Insight: Non-Destr. Test. Condit. Monit. 43 (2001) 607-615.
[65] A. Pacana, K. Czerwinska, L. Bednarova, Comprehensive improvement of the surface quality of the diesel engine piston, Metalurgija 58 (2019) 329-332.
[66] P. Zientek. Non-destructive testing methods for selected elements of small power turbogenerators, Napędy i Sterowanie 19(3) (2017) 114-119.
[67] M. Korzyński et al., Fatigue strength of chromium coated elements and possibility of its improvement with ball peening, Surface & Coatings Technology 204 (2009) 615-620, https://doi.org/10.1016/j.surfcoat.2009.08.049