Investigation of Electromagnetic Properties of Tool Hard Alloys under the Influence of High Temperatures

Investigation of Electromagnetic Properties of Tool Hard Alloys under the Influence of High Temperatures

E.V. Artamonov, A.M. Tveryakov, A.S. Shtin

download PDF

Abstract. The article shows the developed installation for determination of temperature of maximum operability of replaceable cutting hard-alloy plates on the basis of study of change of electromagnetic properties. The method of research is given. Tests of images were carried out to time of heating of the replaceable cutting plates from solid B35 alloy. The heating temperature interval was selected according to the temperature mode of the process of cutting difficult materials. Heating was carried out to 1000˚ C. The results of the study were obtained to determine the temperature of maximum operability of replaceable cutting hard alloy plates based on the study of the change in electromagnetic properties for alloy В35 amounted to 460-730 ° С.

Hard Alloys, Metalworking, Maximum Working Capacity Temperature, Electromagnetic Properties, Cutting

Published online 1/5/2022, 6 pages
Copyright © 2022 by the author(s)
Published under license by Materials Research Forum LLC., Millersville PA, USA

Citation: E.V. Artamonov, A.M. Tveryakov, A.S. Shtin, Investigation of Electromagnetic Properties of Tool Hard Alloys under the Influence of High Temperatures, Materials Research Proceedings, Vol. 21, pp 323-328, 2022


The article was published as article 57 of the book Modern Trends in Manufacturing Technologies and Equipment

Content from this work may be used under the terms of the Creative Commons Attribution 3.0 licence. Any further distribution of this work must maintain attribution to the author(s) and the title of the work, journal citation and DOI.

[1] E.V. Artamonov, Strength and operability of replaceable hard alloy plates of prefabricated cutting tools, Tyumen, Vector Buk, 190. 2003 p. 135.
[2] N.N. Zorev Untersuchung der Kintakt-spannunger auf den Arbeits-flachen des Werkzeugs miteiner Schneidenabrundung, in: N.N. Zorev, M.H. Uteshev – Berichte der Internationalen Forschungesgemein-schaft fur mechanische produktionstechniktionstechnik Vol. 20-1 Schweiz, 1971, pp. 31-32.
[3] Information on
[4] S.A. Vasin Cutting materials: Thermomechanical approach to the system of relationships in cutting: a textbook for technical universities, in: S.A. Vasin, A.S. Vereshchak, V.S. Kushner – M.: Publishing House MSTU named after N.E. Bauman, 2001, p. 448
[5] V.A. Grechishnikov Formation processes and instrumental technique, in: V.A. Grechishnikov, N.A. Chemborisov, V.B. Stupko, D.T. Safarov, O.B. Kuchina, S.N. Grigoriev, A.G. Schirtladze. – Old Oskol: TNT, 2012. p. 328.
[6] V.V. Lapshin, Machining of linear negative matrices for fresnel lenses and prisms, in: V.V. Lapshin, E.M. Zakharevich, S.V. Grubyi – Russian engineering research, Allerton Press, Inc, New York, Vol. 36.10, 2016 pp. 826-830.
[7] I. Carceanu, G. Cosmeleatǎ, B. Ghiban, M. Balanescu, I. Nedelcu, High performance composite materials created through advanced techniques, Materiale Plastice Vol. 44, Issue 4, 2007, pp. 321-325.
[8] C. Ferri, T. Minton, S.B. Ghani, K. Cheng, Internally cooled tools and cutting temperature in contamination-free machining. Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science Vol. 228, Issue 1, 2014, pp. 135-145.
[9] J. Kümmel, D. Braun, J. Gibmeier, J. Schneider, C. Greiner, V. Schulze, A. Wanner, Study on micro texturing of uncoated cemented carbide cutting tools for wear improvement and built-up edge stabilization. Journal of Materials Processing Technology Vol. 215, 2015, pp. 62-70.
[10] Munish Kumar Gupta, Machining of Aerospace Material – Ti (grade-2) alloy: Modelling and Optimization/ Pardeep Kumar Sood, Gurraj Singh, Vishal S. Sharma Sustainable// Journal of Cleaner Production.
[11] K.S. Murthy, I. Rajendran, Optimization of end milling parameters under minimum quantity lubrication using principal component analysis and grey relational analysis. Journal of the Brazilian Society of Mechanical Sciences and Engineering Vol. 34, Issue 3, 2012, pp. 253-261.
[12] R. Neugebauer, C. Hochmuth, G. Schmidt, M. Dix, Energy efficient process planning based on numerical simulations. Advanced Materials Research 2011, Vol. 223, pp. 212-221, 17th CIRP Conference on Modelling of Machining Operations; Sintra; Portugal, 2011.
[13] A. Nurulamin, I. Jaafar, W. Zubaire Role of discrete nature of chip formation and natural vibrations of system components in chatter formation during metal cutting, IIUM Engineering Journal. 2010, Vol. 11, pp. 124-126.
[14] S. Tangjitsitcharoen, T. Moriwaki Intelligent monitoring and identification of cutting states of chips and chatter on CNC turning machine, Journal of Manufacturing Processes. 2008, Vol.10, pp. 40–46.
[15] A. Patwari, Investigations of formation of chatter in a non-wavy surface during thread cutting and turning operations, in: A. Patwari, N. Amin, W. Faris – Text : electronic, Advanced Materials Research. 2010, Vol.83, pp. 637–645.
[16] W. Tillmann, C. Schaak, D. Biermann, R. Abmuth, S. Goeke, Robot based deposition of WC-Co HVOF coatings on HSS cutting tools as a substitution for solid cemented carbide cutting tools. IOP Conference Series: Materials Science and Engineering,Volume 181, Issue 1, 17 March 2017, Vol. 2011 19th Chemnitz Seminar on Materials Engineering; Chemnitz; Germany; 16 March 2017- 17 March 2017.
[17] H. Zhang, Z.Z. Fang, Q. Lu, Characterization of a bilayer WC-Co hardmetal using Hertzian indentation technique. International Journal of Refractory Metals and Hard Materials, Vol. 27, Issue 2, March 2009, pp. 317-322.
[18] C. L. Zhang, A hybrid approach of ANN and HMM for cutting chatter monitoring, in: C. L. Zhang, X. Yue, Y. T. Jiang, – Text : electronic, Advanced Materials Research. 2010, Vol.97, pp. 3225–3232.
[19] E.V. Artamonov, Installation for diagnostics of temperature of maximum operability of replaceable cutting inserts based on change of electromagnetic properties of hard alloys, in: E.V. Artamonov, A.M. Tveryakov, A.S. Shtin Control. Diagnostics. 2018. Vol.12. pp. 54-57.
[20] E.V. Artamonov Determination of Temperature of Maximum Working Capacity of Tool Hard Alloys, in: E.V. Artamonov, А.М. Tveryakov, A.S. Shtin – Text : electronic, Obrabotka metallov-metal working and material science, – 2018. – Vol. 20.3, pp. 47-57.
[21] E.V. Artamonov Development of installation elements for determining the temperature of maximum operability of cutting elements from hard alloys, in: E.V. Artamonov, A.M. Tveryakov, A.S. Shtin .Transport and mechanical engineering of Western Siberia. 2018. Vol. 1. – pp. 31-38.